Hello,
I have a DAC+ that works wonderfully in on my RP3 while running Raspbian.
This is after I configured it usinghttps://www.hifiberry.com/build/document...ux-3-18-x/ .
However, when I do the same exact steps within OpenAuto Pro no sound comes through at all. And I am not sure why.
Here is a cat of my /boot/config.txt any advice would be appreciated.
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtoverlay=hifiberry-dacplus
dtparam=audio=off
#dtoverlay=vc4-kms-v3d
gpu_mem=256
dtoverlay=vc4-fkms-v3d
disable_splash=1
Here is the output of aplay -l
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: sndrpihifiberry [snd_rpi_hifiberry_dacplus], device 0: HiFiBerry DAC+ Pro HiFi pcm512x-hifi-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
I also already posted on HiFiBerry asking for help as well but they directed me here.
https://support.hifiberry.com/hc/en-us/c...o-No-Audio
Thank you!
I have a DAC+ that works wonderfully in on my RP3 while running Raspbian.
This is after I configured it using
However, when I do the same exact steps within OpenAuto Pro no sound comes through at all. And I am not sure why.
Here is a cat of my /boot/config.txt any advice would be appreciated.
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtoverlay=hifiberry-dacplus
dtparam=audio=off
#dtoverlay=vc4-kms-v3d
gpu_mem=256
dtoverlay=vc4-fkms-v3d
disable_splash=1
Here is the output of aplay -l
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: sndrpihifiberry [snd_rpi_hifiberry_dacplus], device 0: HiFiBerry DAC+ Pro HiFi pcm512x-hifi-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
I also already posted on HiFiBerry asking for help as well but they directed me here.
Thank you!