Is there a version 2 coming? or new stock due soon?

Information, updates, questions, issues regarding BWS CAR PS project.
Post Reply
mentalinc
Posts: 18
Joined: Tue Mar 12, 2019 8:19 pm

Is there a version 2 coming? or new stock due soon?

Post by mentalinc » Wed Apr 10, 2019 9:34 am

See they are not available for purchase currently.
Just wondering if there is an ETA for them?

BlueWave
Site Admin
Posts: 522
Joined: Tue Sep 18, 2018 6:30 am

Re: Is there a version 2 coming? or new stock due soon?

Post by BlueWave » Wed Apr 10, 2019 11:59 am

Currently we are struggling with manufacturer and very long delivery time. Therefore we do not want to declare to any ETA.

Albino_Hedgehog
Posts: 5
Joined: Sun Apr 21, 2019 7:41 pm

Re: Is there a version 2 coming? or new stock due soon?

Post by Albino_Hedgehog » Fri Apr 26, 2019 10:10 am

Any update on this?

This sort of hardware is very make or break for this sort of project.

Is it definitely coming back in stock? Or should I focus on looking for an alternative?

BlueWave
Site Admin
Posts: 522
Joined: Tue Sep 18, 2018 6:30 am

Re: Is there a version 2 coming? or new stock due soon?

Post by BlueWave » Sat May 04, 2019 9:08 am

Sorry the boards have been damaged during manufacture process and we try to solve these issues with supplier.

For now you can try Hisma solution which is very simple and interesting:
https://bluewavestudio.io/forum/viewtop ... 1818#p1818

mentalinc
Posts: 18
Joined: Tue Mar 12, 2019 8:19 pm

Re: Is there a version 2 coming? or new stock due soon?

Post by mentalinc » Mon May 06, 2019 9:49 am

I have configured per Hisma steps and just need to test in the car, but can't see why it wouldn't work!

BlueWave
Site Admin
Posts: 522
Joined: Tue Sep 18, 2018 6:30 am

Re: Is there a version 2 coming? or new stock due soon?

Post by BlueWave » Mon May 06, 2019 5:46 pm

What do you mean, by this?
can't see why it wouldn't work!

mentalinc
Posts: 18
Joined: Tue Mar 12, 2019 8:19 pm

Re: Is there a version 2 coming? or new stock due soon?

Post by mentalinc » Fri May 17, 2019 7:04 pm

I hadn't validated i could reproduce what @Hisma had created.
I have now done that and works 100% as expected.
Suggest you point people in that direction.

I wrote up what the video did to help along on my build:

###
Resetting Timer to the factory settings.
###
To reset the timer to the factory settings perform the following procedure:
Connect WHITE/GREEN wires to the ground or push button #1 and #2.
Supply power to the timer.
When output comes on (LED ON) disconnect power while keeping WHITE/GREEN wires connected to the ground.
Repeat supply and disconnect of power five times.
On the fifth time, the output will blink a couple times.
Disconnect WHITE/GREEN from the ground and wait until LED goes OFF.
Disconnect power. Timer is reset to the default values.

###
Wiring
###

Blue = GPIO
Red = power
Black = ground
Yellow & Red

Light goes to yellow and black
Battery goes to red and black


###
HMS Mode
###


https://youtu.be/rknBevexOcU?t=367
Touch GREEN and WHITE to GROUND, apply power, then remove GREEN and WHITE from GROUND, light should stay on three seconds = programming mode

Touch GREEN and WHITE to GROUND four more times (waiting for the light to turn off each time)

Touch GREEN to GROUND,, then take GREEN off GROUND, light should flash twice

Pull power

###
Set to shut off after 1 hour
###

Touch GREEN and WHITE to GROUND, apply power, then remove GREEN and WHITE from GROUND, light should stay on three seconds = programming mode

WHITE touch and hold to GROUND 4 times = four paramters (light will "strobe"
watch and follow
https://youtu.be/rknBevexOcU?t=460

then VERY quickly touch WHITE to GROUND so light just flashes to set 1 hour

WHITE to GROUND and hold to save. light flashes a few times

then WHITE to GROUND 4 more times (light flashes for a bit) to skip the paramters, then the light says on after fourth touch

remove power


###
Delay time off type
###
https://youtu.be/rknBevexOcU?t=519

Touch GREEN and WHITE to GROUND, apply power, then remove GREEN and WHITE from GROUND, light should stay on three seconds = programming mode

Touch GREEN and WHITE to GROUND once - light stays on for a bit

WHITE to GROUND 12 times (light on each time)

wait a bit

then GREEN to GROUND two touches

remove power

Post Reply