-Problem 1 Touch Screen not work in OpenAuto Pro (Only Raspbian)
Raspberry Pi 3 B+ with Micro SD Card 16gb (Class U1)
Longruner 7 Inch LCD Screen (800x480) touch only run in raspbian, does not work with open openauto.
OpenAuto Pro 3.3.1
Powersupply 5v 2.5A for raspberry
Powersupply 5v 2A for to screen
Archive config.txt
# For more options and information see
# http://www.raspberrypi.org/documentation...fig-txt.md
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=87
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=off
#dtparam=i2s=on
dtparam=spi=off
enable_uart=0
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
max_usb_current=1
hdmi_force_hotplug=1
config_hdmi_boost=7
hdmi_group=2
hdmi_mode=87
hdmi_mode=87
hdmi_drive=1
hdmi_cvt 800 480 60 6 0 0 0
gpu_mem=320
dtoverlay=vc4-fkms-v3d
-Problem 2 Android Auto load in black screen
Android Mobile: OnePlus 6T
Android Version: 9 (OxigenOS 9.0.16)
Android Auto App Verison: 4.5.592854
Connection by usb
For this problem I have also tried all the solutions described in the forum and they do not work
Raspberry Pi 3 B+ with Micro SD Card 16gb (Class U1)
Longruner 7 Inch LCD Screen (800x480) touch only run in raspbian, does not work with open openauto.
OpenAuto Pro 3.3.1
Powersupply 5v 2.5A for raspberry
Powersupply 5v 2A for to screen
Archive config.txt
# For more options and information see
# http://www.raspberrypi.org/documentation...fig-txt.md
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=87
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=off
#dtparam=i2s=on
dtparam=spi=off
enable_uart=0
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
max_usb_current=1
hdmi_force_hotplug=1
config_hdmi_boost=7
hdmi_group=2
hdmi_mode=87
hdmi_mode=87
hdmi_drive=1
hdmi_cvt 800 480 60 6 0 0 0
gpu_mem=320
dtoverlay=vc4-fkms-v3d
-Problem 2 Android Auto load in black screen
Android Mobile: OnePlus 6T
Android Version: 9 (OxigenOS 9.0.16)
Android Auto App Verison: 4.5.592854
Connection by usb
For this problem I have also tried all the solutions described in the forum and they do not work