Current version of the OpenAuto Pro is 11
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
System configuration (openauto_system.ini)
#11
Quote:[Bluetooth]
; Type of the Bluetooth adapter exposed to the Android Auto for Hands-Free calling purposes.
; (0 - None, 1 - Local, 2 - Remote).

AdapterType=0

; MAC address of the Remote Bluetooth device (e.g. in-car Bluetooth receiver) that will be send to the Android Auto. Phone must be paired with that device.
; Example: 00:11:22:33:44:55
RemoteAdapterAddress=
#12
Quote:[Obd]
; List of the AT commands that will be send to the ELM327 adapter after connection establishment. AT commands can be used to select OBD-II protocol variant, reset the ELM327 adapter or adjust various parameters, e.g. internal timers. More info can be found at https://www.elmelectronics.com/wp-conten...M327DS.pdf
ObdAdapterStartupSequence=ATZ;ATE0;ATS0;ATL0;ATH0;ATSP0

; Path to the ELM327 device descriptor (e.g. /dev/ttyUSB0). Relevant only for adapters connected via USB.
ObdAdapterDescriptor=

Baudrate of the ELM327 serial interface. This is the baudrate used to communicate between ELM327 adapter and Raspberry PI. It has nothing to do with baudrate of the OBD port. Relevant only for adapters connected via USB. More information about supported baudrate can be found in user manual of used ELM327 adapter.
ObdAdapterBaudrate=115200

; Delay in ms between each request of a PID value. Lowering the period will increase refreshment rate of PID values. Increasing the period may improve stability of the connection (in case of any problems).
ObdProbePeriod=5

; Type of the ELM327 adapter.
; (0 - None, 1 - USB, 2 - Bluetooth).
ObdDeviceType=0

; MAC address of the ELM327 Bluetooth adapter.
; Example: 00:11:22:33:44:55.
ObdAdapterRfCommAddress=

; Id of the RfComm channel exposed by the ELM327 Bluetooth firmware. Relevant only for adapters connected via Bluetooth. More details about RfComm channel ID can be found in user manual of used adapter.
ObdAdapterRfCommChannel=1

; Number of allowed NO DATA responses received from ELM327 adapter after querying PID values. Exciding the limit will result in reset of the connection to the adapter.
ObdMaxNoDataResponseCount=20
#13
Quote:[Wireless]
; Enable/disable functionality of wireless Android Auto.
Enabled=false

; Name of the Hotspot served by the Raspberry PI.
; If Hotspot is disabled this value stores name of the external Wireless network that will be used for Android Auto connection.

Ssid=OpenAutoPro

; MAC address of the access point that will be used for wireless Android Auto connection.
; Set it only when Hotspot is disabled and you want to use external Wireless network for Android Auto connection.

Bssid=

; Password of the Hotspot wireless network.
; If Hotspot is disabled this value stores password to the external Wireless network that will be used for Android Auto connection.

Key=1234567890

; Port to listening for incoming wireless Android Auto connections.
Port=5000

; Band of the Hotspot
; (0 - 2.4GHz, 1 - 5Ghz)

HotspotBand=0
#14
Quote:[Media]
; Default path to the folder with media files. This value will be used in embdded file browser.
DefaultStoragePath=/media
#15
Quote:[RearCamera]
; Path to the camera device descriptor (in case of V4L2 backend)
DeviceDescriptor=v4l2:///dev/video0

; GPIO Pin to trigger rear camera view (LOW - hide camera view, HIGH - show camera view)
GpioPin=0

; Show/Hide guideline on camera view
ShowGuideLine=false

; Orientation of the camera view (in case of Finder backend)
Orientation=0

; Type of the rear view camera backend.
; 0 - Finder, 1 - V4L2
BackendType=0

; Width of the camera video stream (in case of Finder backend)
ResolutionWidth=1280

; Height of the camera video stream (in case of Finder backend)
ResolutionHeight=720

; Index of the connected device that will be used as rear camera.
ViewFinderIndex=0

; Enable/disable volume level change when rear camera is active (GPIO is in High state)
VolumeLevelEnabled=false

; Absolute volume level that will be set when rear camera is active (GPIO is in High state)
VolumeLevel=70


Forum Jump:


Users browsing this thread: 1 Guest(s)